check engine MERCEDES-BENZ CLK350 2007 A209 Owner's Manual

Contents
At the gas station .............................. 312
Refueling ...................................... 312
Check regularly
and before a long trip ................... 314
Engine compartment ......................... 315
Hood ............................................ 315
Engine oil ..................................... 317
Transmission fluid level ................ 319
Coolant ........................................ 320
Battery ......................................... 321
Windshield washer system and
headlamp cleaning system* ......... 322
Tires and wheels ................................ 323
Important guidelines .................... 323
Tire care and maintenance........... 324
Direction of rotation ..................... 326
Loading the vehicle ...................... 326
Recommended
tire inflation pressure ................... 331
Checking tire inflation pressure ... 333
MOExtended system* .................. 336
Tire labeling.................................. 337
Load identification ....................... 341
DOT,
Tire Identification Number (TIN) ... 342
Maximum tire load ....................... 343Maximum tire inflation pressure ... 344
Uniform Tire Quality Grading
Standards (U.S. vehicles) .............. 344
Tire ply material ............................ 346
Tire and loading terminology......... 347
Rotating tires ................................ 350
Winter driving ..................................... 351
Winter tires ................................... 351
Block heater (Canada only) ........... 352
Snow chains.................................. 352
Maintenance....................................... 353
Maintenance
service indicator message ............ 353
Clearing the maintenance
service indicator message ............ 354
Maintenance
service term exceeded.................. 354
Calling up the maintenance
service indicator display ............... 355
Resetting the maintenance
service indicator ........................... 355
Vehicle care........................................ 356
Cleaning and care of vehicle ......... 356
Practical hints.................................. 365
What to do if …? ................................. 366
Lamps in instrument cluster ......... 366
Lamp in center console ................ 376
Vehicle status messages
in the multifunction display .......... 378
Where will I find...? ............................. 404
First aid kit.................................... 404
TIREFIT (CLK 63 AMG only)........... 404
Vehicle tool kit.............................. 404
Minispare wheel............................ 407
Spare wheel bolts ......................... 409
Unlocking/locking in an emergency .. 410
Unlocking the vehicle ................... 410
Locking the vehicle ....................... 411
Manually unlocking
the gear selector lever .................. 412
Opening/closing in an emergency ..... 413
Operating roll bars manually ......... 413
Soft top emergency operation ...... 415
Resetting activated head restraints.... 424
Resetting activated
head restraints ............................. 424

23 At a glance
Exterior view
ItemPage
1Trunk
Unlocking
Opening and closing
Minispare wheel
Vehicle tool kit
34
109,
110
407
404
2Rear lamps432
3Rear window, defrosting187
4Fuel filler flap
Refueling
Gasoline312
312
475
5Doors
Locking and unlocking
Closing
Unlocking/locking in an
emergency
34, 62,
98
108
410
ItemPage
6Exterior rear view mirror
Adjusting
Auto-dimming rear view
mirrors
45
185
7Tires and wheels
Checking tire inflation pres-
sure
Run Flat Indicator*
General information
TIREFIT Kit (CLK 63 AMG)
Vehicle tool kit
Minispare wheel
Flat tire323
333
334
323
404
404
407
436
8Towing
Installing towing eye bolt452
454
9Front lamps430
ItemPage
aHood, opening
Engine oil
Coolant
Battery315
317
320
321
bWindshield wipers
Wiper blades, replacing
Wiper blades, cleaning55
434
362
cWindshield
Front window, defrosting
Cleaning with wiper fluid
Cleaning
189,
199
56
362
dSoft top
Opening and closing
Opening and closing in an
emergency
Roll bars
Cleaning
255
415
81
359

36 Getting started
Unlocking
Starter switch positions
SmartKey
Starter switch
0For removing SmartKey
The steering is locked when the
SmartKey is removed from the starter
switch.
1Power supply for some electrical
consumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position
All lamps (except low beam headlamp
indicator lamp, high beam headlamp in-
dicator lamp, and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary. If
a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 366).
3Starting position
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
iWhen you switch on the ignition, the
indicator and warning lamps (except low beam
headlamp indicator lamp, high beam headlamp
indicator lamp, and turn signal indicator lamps
unless activated) in the instrument cluster come
on. The indicator and warning lamps (except low
beam headlamp indicator lamp, high beam head-
lamp indicator lamp, and turn signal indicator
lamps if activated) will go out when the engine is
running. This indicates that the respective sys-
tems are operational.
iThe SmartKey can only be removed from the
starter switch with the gear selector lever in
positionP.
iIf the SmartKey is left in starter switch
position0 for an extended period of time, it can
no longer be turned in the switch. In this case,
the steering is locked. To unlock, remove
SmartKey from starter switch and reinsert.

37 Getting started
Unlocking
For more information, see “SmartKey”
(
page 98).
For information on starting the engine us-
ing the SmartKey, see “Starting with the
SmartKey” (
page 51).SmartKey with KEYLESS-GO*
Pressing the KEYLESS-GO start/stop but-
ton on the gear selector lever corresponds
to turning the SmartKey to the various
starter positions.
If you firmly depress the brake pedal dur-
ing pressing the KEYLESS-GO start/stop
button, the engine starts automatically.
You can also use the SmartKey with
KEYLESS-GO like a normal SmartKey.
KEYLESS-GO start/stop button
1USA only
2Canada only
The SmartKey with KEYLESS-GO must be
located in the vehicle.
Make sure the gear selector lever is set
toP.
Do not depress the brake pedal.
!If the SmartKey cannot be turned in the
starter switch, the battery may not be sufficient-
ly charged.

Check the battery and charge it if necessary
(
page 447).

Get a jump start (page 450).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.
iThe function of the SmartKey overrules the
KEYLESS-GO function.

38 Getting started
Unlocking
Position 0
Before you press the KEYLESS-GO
start/stop button, the vehicle’s on-board
electronics have status0 (as with
SmartKey removed).
Position 1
Press the KEYLESS-GO start/stop
button once.
This supplies power for some electrical
consumers, such as seat adjustment.Ignition (or position 2)
Press the KEYLESS-GO start/stop but-
ton twice.
This supplies power for all electrical
consumers. All the lamps (except low
beam headlamp indicator lamp, high
beam headlamp indicator lamp, and
turn signal indicator lamps unless acti-
vated) in the instrument cluster come
on. If a lamp in the instrument cluster
fails to come on when the ignition is
switched on, have it checked and re-
placed if necessary. If a lamp in the in-
strument cluster remains on after
starting the engine or comes on while
driving, refer to “Lamps in instrument
cluster”(
page 366).For more information, see “SmartKey with
KEYLESS-GO*” (
page 101).
For information on starting the engine
using the KEYLESS-GO start/stop button,
see “Starting with KEYLESS-GO*”
(
page 51).
iIf you now press the KEYLESS-GO
start/stop button

once again, the ignition (position2) is
switched on.

twice, the power supply is again switched
off.
iIf you now press the KEYLESS-GO
start/stop button once, the power supply is
again switched off.
iWhen you switch on the ignition, the indica-
tor and warning lamps (except low beam head-
lamp indicator lamp, high beam headlamp
indicator lamp, and turn signal indicator lamps
unless activated) in the instrument cluster come
on. The indicator and warning lamps (except low
beam headlamp indicator lamp, high beam head-
lamp indicator lamp, and turn signal indicator
lamps if activated) will go out when the engine is
running. This indicates that the respective sys-
tems are operational.

57 Getting started
Driving
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.

The engine electronics may not be op-
erating properly.

Unburned gasoline may have entered
the catalytic converter and damaged it.
Give very little gas.
Have the problem repaired by an au-
thorized Mercedes-Benz Center as
soon as possible.
The coolant temperature is
above 248°F (120°C)
The coolant is too hot and is no longer
cooling the engine.
Stop the vehicle in a safe location as
soon as possible and turn off the en-
gine. Allow engine and coolant to cool
off.
Check the coolant level and add
coolant if necessary (
page 320).
In case of accident
If the vehicle is leaking gasoline:
Do not start the engine under any cir-
cumstances.
Notify local fire and/or police authori-
ties.
If the extent of the damage cannot be de-
termined:
Notify an authorized Mercedes-Benz
Center.
If no damage can be determined on the

major assemblies

fuel system

engine mount:
Start the engine in the usual manner.
!If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediate-
ly.

For safety reasons, stop the vehicle in a safe
location and,

remove SmartKey from starter switch
or

turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, starter switch is in position 0,
same as with SmartKey removed from
starter switch)
before attempting to remove any blockage.

Remove blockage.

Turn the windshield wipers on again.
If windshield wipers fail to function at all in com-
bination switch positionI,

set the combination switch to the next high-
er wiper speed

have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center.

81 Safety and Security
Occupant safety
Roll bars
The roll bars are integrated into the rear
head restraints.
The roll bars raise automatically in an acci-
dent or in a critical driving situation.
You can manually lower the roll bars again
when the soft top is open (
page 414).
With the soft top closed, contact an autho-
rized Mercedes-Benz Center to have the
roll bars lowered. Do not attempt to lower
the roll bars manually with the soft top closed. Lowering the roll bars manually
with the soft top closed may impair the
function of the roll bars.
Warning!G
Make sure nothing is blocking the roll bars’
path of motion. Otherwise someone could
be injured when the roll bars are raised. The
head restraints should therefore always be
in the raised position when the rear seat is
occupied (
page 120).
iWhen the roll bars are raised automatically,
you will hear a ratcheting sound and the rear
head restraints will also rise.
iYou cannot lower the rear head restraints
with the rear head restraint lowering switch
(
page 120) when the roll bars are in the raised
position.
Also, you cannot operate the soft top using the
soft top switch when the roll bars are in the
raised position.

If the soft top is open, you can manually low-
er the roll bars (
page 414).

If the soft top is closed, contact an autho-
rized Mercedes-Benz Center to have the roll
bars lowered.
Warning!G
If the yellow roll bar warning lamp in
the clock does not go out after starting the
engine, or if it comes on while driving, then
the roll bar system is not operating properly
and may not activate in an accident. In this
case, raise the roll bars manually before
continuing to drive (
page 413).
For safety reasons, drive only with the roll
bars raised until the malfunction is repaired.
Have your vehicle checked at an authorized
Mercedes-Benz Center.

103 Controls in detail
Locking and unlocking
Important notes on using KEYLESS-GO*

You can also use the SmartKey with
KEYLESS-GO like a normal SmartKey
(
page 98).

You can combine KEYLESS-GO func-
tions with normal SmartKey functions
(e.g. unlocking with KEYLESS-GO and
locking with the ‹button).

Always carry the SmartKey with
KEYLESS-GO with you.

Never store the SmartKey with
KEYLESS-GO together with:

Electronic items such as a cellular
phone or another SmartKey with
KEYLESS-GO.

Metallic objects such as coins or
metal foil.
Doing so could impair the function of
the KEYLESS-GO system.

To lock or unlock the vehicle, the
SmartKey with KEYLESS-GO must be
located outside the vehicle within ap-
proximately 3 ft (1 m) of the door to be
opened or the trunk lid.

In order to start the engine with the
SmartKey with KEYLESS-GO:

The SmartKey with KEYLESS-GO
must be located in the vehicle.

All doors must be closed.

The brake pedal must be firmly de-
pressed. Do not depress the accel-
erator.

If the SmartKey with KEYLESS-GO is
positioned farther away from the vehi-
cle, the system may no longer recog-
nize the SmartKey with KEYLESS-GO.
The vehicle then cannot be locked or
the engine started via the KEYLESS-GO
system.

If the SmartKey with KEYLESS-GO is re-
moved from the vehicle (e.g. if passen-
ger exits the vehicle with the SmartKey
with KEYLESS-GO)
!If you can no longer lock or unlock the vehi-
cle with the SmartKey with KEYLESS-GO, then
the batteries in the SmartKey with KEYLESS-GO
are discharged, the SmartKey with KEYLESS-GO
is malfunctioning or the vehicle battery is
drained.

Check the batteries in the SmartKey with
KEYLESS-GO (
page 107) and replace
them if necessary (
page 425).

Use the mechanical key to unlock the driv-
er’s door (
page 410) and the trunk
(
page 411).

Use the mechanical key to lock the driver’s
door (
page 411) and the trunk
(
page 117).

Have the vehicle battery and the battery con-
nections checked (
page 447).
If the SmartKey with KEYLESS-GO is malfunc-
tioning, contact an authorized Mercedes-Benz
Center.

183 Controls in detail
Automatic transmission
Downshifting
Briefly press the gear selector lever to
the left in theD-direction.
or
Briefly pull left shift paddle1
(
page 179).
The transmission shifts to the next
lower gear.Kickdown
Using the kickdown when driving in the
manual program modeM is not possible.
Deactivating manual shift program
Press the program mode selector
switch (
page 181) repeatedly
until
CorS appears in the multifunction
display.
or
Restart the engine.
The transmission will go to the
automatic program mode (C orS).
The manual program modeM is not
stored.Emergency operation
(Limp-Home Mode)
If vehicle acceleration becomes less re-
sponsive or sluggish or the transmission
no longer shifts, the transmission is most
likely operating in limp-home (emergency
operation) mode. In this mode only second
gear and reverse gear can be selected.
Stop the vehicle in a safe location.
Move the gear selector lever to park
positionP.
Turn off the engine.
Wait at least 10 seconds before
restarting.
Restart the engine.
Move the gear selector lever to
positionD (for second gear) or
positionR.
Have the transmission checked at an
authorized Mercedes-Benz Center as
soon as possible.
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced
vehicle control. Your vehicle’s ABS will not
prevent this type of loss of control.
iWhen you brake or stop, the transmission
shifts down to a gear from which you can easily
accelerate or take off.

196 Controls in detail
Climate control
Air conditioning
The cooling function, is only operational
when the engine is running, cools the vehi-
cle interior down to the selected tempera-
ture. The cooling function also
dehumidifies the air in the vehicle interior,
thus preventing the windows from fogging
up.Deactivating
It is possible to deactivate the air condi-
tioning (cooling) function of the climate
control system. The air in the vehicle will
then no longer be cooled or dehumidified.
Press button2(page 189).
The indicator lamp on the button goes
out.
The cooling function switches off after
a short delay.
Activating
Moist air can fog up the windows. You can
dehumidify the air with the air condition-
ing.
Press button2(page 189) again.
The indicator lamp on the button
comes on.The air conditioning uses the
refrigerant R134a. This refrigerant is free
of CFCs which are harmful to the ozone
layer.
iCondensation may drip out from underneath
the vehicle. This is normal and not an indication
of a malfunction.
Warning!G
If you turn off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog
up more quickly. Window fogging may
impair visibility and endanger you and
others.
!If the air conditioning cannot be turned on
again, this indicates that the air conditioning is
losing refrigerant. The compressor has turned it-
self off.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Center.